Get Free Ebook ASM Handbook Volume 1: Properties and Selection: Irons, Steels, and High-Performance Alloys (06181)From Brand: ASM International
As understood, adventure as well as experience concerning lesson, amusement, and also expertise can be gotten by just reading a publication ASM Handbook Volume 1: Properties And Selection: Irons, Steels, And High-Performance Alloys (06181)From Brand: ASM International Also it is not directly done, you could recognize even more about this life, about the globe. We offer you this appropriate as well as very easy way to get those all. We offer ASM Handbook Volume 1: Properties And Selection: Irons, Steels, And High-Performance Alloys (06181)From Brand: ASM International as well as numerous book collections from fictions to science in any way. One of them is this ASM Handbook Volume 1: Properties And Selection: Irons, Steels, And High-Performance Alloys (06181)From Brand: ASM International that can be your companion.
ASM Handbook Volume 1: Properties and Selection: Irons, Steels, and High-Performance Alloys (06181)From Brand: ASM International
Get Free Ebook ASM Handbook Volume 1: Properties and Selection: Irons, Steels, and High-Performance Alloys (06181)From Brand: ASM International
ASM Handbook Volume 1: Properties And Selection: Irons, Steels, And High-Performance Alloys (06181)From Brand: ASM International. Give us 5 minutes as well as we will show you the most effective book to review today. This is it, the ASM Handbook Volume 1: Properties And Selection: Irons, Steels, And High-Performance Alloys (06181)From Brand: ASM International that will be your best choice for far better reading book. Your five times will not spend squandered by reading this internet site. You can take the book as a source making better concept. Referring guides ASM Handbook Volume 1: Properties And Selection: Irons, Steels, And High-Performance Alloys (06181)From Brand: ASM International that can be located with your needs is at some time tough. But below, this is so easy. You could discover the best thing of book ASM Handbook Volume 1: Properties And Selection: Irons, Steels, And High-Performance Alloys (06181)From Brand: ASM International that you could check out.
The means to get this publication ASM Handbook Volume 1: Properties And Selection: Irons, Steels, And High-Performance Alloys (06181)From Brand: ASM International is really simple. You might not go for some places and also spend the time to just find guide ASM Handbook Volume 1: Properties And Selection: Irons, Steels, And High-Performance Alloys (06181)From Brand: ASM International In fact, you might not consistently get the book as you agree. Yet right here, just by search and discover ASM Handbook Volume 1: Properties And Selection: Irons, Steels, And High-Performance Alloys (06181)From Brand: ASM International, you could obtain the listings of guides that you actually expect. In some cases, there are many publications that are showed. Those books of course will certainly amaze you as this ASM Handbook Volume 1: Properties And Selection: Irons, Steels, And High-Performance Alloys (06181)From Brand: ASM International compilation.
Are you thinking about mainly books ASM Handbook Volume 1: Properties And Selection: Irons, Steels, And High-Performance Alloys (06181)From Brand: ASM International If you are still confused on which one of guide ASM Handbook Volume 1: Properties And Selection: Irons, Steels, And High-Performance Alloys (06181)From Brand: ASM International that need to be bought, it is your time to not this site to seek. Today, you will certainly need this ASM Handbook Volume 1: Properties And Selection: Irons, Steels, And High-Performance Alloys (06181)From Brand: ASM International as the most referred publication as well as the majority of required book as sources, in other time, you could enjoy for some other publications. It will certainly depend upon your ready requirements. However, we constantly recommend that publications ASM Handbook Volume 1: Properties And Selection: Irons, Steels, And High-Performance Alloys (06181)From Brand: ASM International can be a terrific infestation for your life.
Even we talk about the books ASM Handbook Volume 1: Properties And Selection: Irons, Steels, And High-Performance Alloys (06181)From Brand: ASM International; you could not discover the published books here. So many collections are provided in soft documents. It will precisely give you a lot more benefits. Why? The first is that you may not need to lug guide everywhere by fulfilling the bag with this ASM Handbook Volume 1: Properties And Selection: Irons, Steels, And High-Performance Alloys (06181)From Brand: ASM International It is for the book is in soft documents, so you can wait in gadget. After that, you can open up the gadget almost everywhere and review the book properly. Those are some few benefits that can be got. So, take all benefits of getting this soft data publication ASM Handbook Volume 1: Properties And Selection: Irons, Steels, And High-Performance Alloys (06181)From Brand: ASM International in this internet site by downloading in web link supplied.
A comprehensive guide to compositions, properties, performance, and selection of cast irons, carbon and low-alloy steels, tool steels, stainless steels, and superalloys. Contains 1,328 illustrations (photographs, charts, and graphs). More than 500 tables provide extensive data for alloy designations, compositions, and mechanical and physical properties.
- Sales Rank: #1463796 in Books
- Brand: Brand: ASM International
- Published on: 1990-04-01
- Original language: English
- Number of items: 1
- Dimensions: 11.75" h x 9.75" w x 2.75" l, 1.10 pounds
- Binding: Hardcover
- 1063 pages
- Used Book in Good Condition
Review
Cast irons are described in six articles. The introductory article on Classification and Basic Metallurgy of Cast Irons was completely rewritten for the 10th Edition. The article on Compacted Graphite Iron is new to the Handbook. Both of these contributions were authored by D.M. Stefanescu (The University of Alabama), who served as Chairman of Volume 15, Casting, of the 9th Edition. The remaining four articles contain new information on materials (for example, austempered ductile iron) and testing (for example, dynamic tear testing).
Carbon and Low-Alloy Steels. Key additions to this section include articles that explain the relationships among processing (both melt and rolling processes), microstructures, and properties of steels. Of particular note is the article by G. Krauss (Colorado School of Mines) on pages 126 to 139 and the various articles on high-strength low-alloy steels. Other highlights include an extensive tabular compilation that cross-references SAE-AISI steels to their international counterparts (see the article Classification and Designation of Steels ) and an article on Bearing Steels that compares both case-hardened and through-hardened bearing materials.
Hardenability of Carbon and Low-Alloy Steels. Following articles that introduce H-steels and describe hardenability concepts, including test procedures to determine the hardening response of steels, a comprehensive collection of hardenability curves is presented. Both English and metric hardenability curves are provided for some 86 steels.
Fabrication Characteristics. Sheet formability, forgeability, machinability, and weldability are described next. The article on bulk formability, which emphasizes recent studies on HSLA forging steels, is new to the Handbook series. The material on weldability was completely rewritten and occupies nearly four times the space allotted in the 9th Edition.
Service Characteristics. The influence of various in-service environments on the properties of steels is one of the most widely studied subjects in metallurgy. Among the topics described in this section are elevated-temperature creep properties, low-temperature fracture toughness, fatigue properties, and impact toughness. A new article also describes the deleterious effect of neutron irradiation on alloy and stainless steels. Of critical importance to this section, however, is the definitive treatise on Embrittlement of Steels written by G.F. Vander Voort (Carpenter Technology Corporation). Featuring more than 75 graphs and 372 references, this 48-page article explores the causes and effects of both thermal and environmental degradation on a wide variety of steels. Compared with the 9th Edition on the same subject, this represents a nearly tenfold increase in coverage.
Specialty Steels and Heat-Resistant Alloys. Eleven articles on wrought, cast, and powder metallurgy materials for specialty and/or high-performance applications make up this section. Alloy development and selection criteria as related to corrosion-resistant and heat-resistant steels and superalloys are well documented. More than 100 pages are devoted to stainless steels, while three new articles have been written on superalloys including one on newly developed directionally solidified and single-crystal nickel-base alloys used for aerospace engine applications.
Special Engineering Topics. The final section examines two subjects that are becoming increasingly important to the engineering community: (1) the availability and supply of strategic materials, such as chromium and cobalt, used in stainless steel and superalloy production, and (2) the current efforts to recycle highly alloyed materials. Both of these subjects are new to the Handbook series. A second article on recycling of nonferrous alloys will be published in Volume 2 of the 10th Edition. --ASM International
From the Publisher
Published: 1990
About the Author
Cast irons are described in six articles. The introductory article on Classification and Basic Metallurgy of Cast Irons was completely rewritten for the 10th Edition. The article on Compacted Graphite Iron is new to the Handbook. Both of these contributions were authored by D.M. Stefanescu (The University of Alabama), who served as Chairman of Volume 15, Casting, of the 9th Edition. The remaining four articles contain new information on materials (for example, austempered ductile iron) and testing (for example, dynamic tear testing).
Carbon and Low-Alloy Steels. Key additions to this section include articles that explain the relationships among processing (both melt and rolling processes), microstructures, and properties of steels. Of particular note is the article by G. Krauss (Colorado School of Mines) on pages 126 to 139 and the various articles on high-strength low-alloy steels. Other highlights include an extensive tabular compilation that cross-references SAE-AISI steels to their international counterparts (see the article Classification and Designation of Steels ) and an article on Bearing Steels that compares both case-hardened and through-hardened bearing materials.
Hardenability of Carbon and Low-Alloy Steels. Following articles that introduce H-steels and describe hardenability concepts, including test procedures to determine the hardening response of steels, a comprehensive collection of hardenability curves is presented. Both English and metric hardenability curves are provided for some 86 steels.
Fabrication Characteristics. Sheet formability, forgeability, machinability, and weldability are described next. The article on bulk formability, which emphasizes recent studies on HSLA forging steels, is new to the Handbook series. The material on weldability was completely rewritten and occupies nearly four times the space allotted in the 9th Edition.
Service Characteristics. The influence of various in-service environments on the properties of steels is one of the most widely studied subjects in metallurgy. Among the topics described in this section are elevated-temperature creep properties, low-temperature fracture toughness, fatigue properties, and impact toughness. A new article also describes the deleterious effect of neutron irradiation on alloy and stainless steels. Of critical importance to this section, however, is the definitive treatise on Embrittlement of Steels written by G.F. Vander Voort (Carpenter Technology Corporation). Featuring more than 75 graphs and 372 references, this 48-page article explores the causes and effects of both thermal and environmental degradation on a wide variety of steels. Compared with the 9th Edition on the same subject, this represents a nearly tenfold increase in coverage.
Specialty Steels and Heat-Resistant Alloys. Eleven articles on wrought, cast, and powder metallurgy materials for specialty and/or high-performance applications make up this section. Alloy development and selection criteria as related to corrosion-resistant and heat-resistant steels and superalloys are well documented. More than 100 pages are devoted to stainless steels, while three new articles have been written on superalloys including one on newly developed directionally solidified and single-crystal nickel-base alloys used for aerospace engine applications.
Special Engineering Topics. The final section examines two subjects that are becoming increasingly important to the engineering community: (1) the availability and supply of strategic materials, such as chromium and cobalt, used in stainless steel and superalloy production, and (2) the current efforts to recycle highly alloyed materials. Both of these subjects are new to the Handbook series. A second article on recycling of nonferrous alloys will be published in Volume 2 of the 10th Edition.
Most helpful customer reviews
0 of 0 people found the following review helpful.
Lots of great information. This was one of the best things ...
By Mike B
Lots of great information. This was one of the best things I bought for my job. I would recommend it to anyone working with typical steels.
4 of 4 people found the following review helpful.
A Captivating Summer (Job) Read
By Colin Gore
Time and time again, I realize that I should have consulted the ASM Handbook earlier and more often during research. While it does not include the most recent research in the field (last update was in the 90's) it is a great primer for background knowledge in various metals phenomena. Each volume is a massive tome, but they offer a prolific "specific usefulness" factor (both by weight and by volume), so do not be intimidated.
And while some may claim that you're not reading them for the plot, the ASM guides offer many plots, tables, and micrographs for your consulting pleasure.
0 of 0 people found the following review helpful.
You don't have to like it.
By M. Medici
Let's face it. You don't have to like this book. You're not buying it for the plot. You either need it or you don't.
Plenty of info for the materials guy or gal. I bought it used.
ASM Handbook Volume 1: Properties and Selection: Irons, Steels, and High-Performance Alloys (06181)From Brand: ASM International PDF
ASM Handbook Volume 1: Properties and Selection: Irons, Steels, and High-Performance Alloys (06181)From Brand: ASM International EPub
ASM Handbook Volume 1: Properties and Selection: Irons, Steels, and High-Performance Alloys (06181)From Brand: ASM International Doc
ASM Handbook Volume 1: Properties and Selection: Irons, Steels, and High-Performance Alloys (06181)From Brand: ASM International iBooks
ASM Handbook Volume 1: Properties and Selection: Irons, Steels, and High-Performance Alloys (06181)From Brand: ASM International rtf
ASM Handbook Volume 1: Properties and Selection: Irons, Steels, and High-Performance Alloys (06181)From Brand: ASM International Mobipocket
ASM Handbook Volume 1: Properties and Selection: Irons, Steels, and High-Performance Alloys (06181)From Brand: ASM International Kindle
Tidak ada komentar:
Posting Komentar